This is the width that you will see on most 2005 - 08 Mustangs. Available with or without pinstripes. See links at bottom of page.

Here is what you will receive:

1. Precut panel for the front bumper plus a small piece for the valance. (bottom of the air dam) Cut for the GT but can be trimmed to fit the V6 model also. You can either trim around the tag area or cut it straight at the front edge of the bumper.

2. Precut panel for the rear deck. Goes from the rear window around the brake light and gas cap. Fits both GT and V6 models.

3. Precut panel for the rear bumper. Fits both GT and V6 models.

4. 20 feet of 10" wide striping for the hood and roof. YOU WILL CUT THESE TO FIT. This gives you more flexibility and makes the kit easier to install. It also gives you extra material for the spoiler, etc.. It also allows me to sell this kit for far less than anyone else.

The stripes are designed to be spaced apart about 2 inches.

You will also receive instructions and a squeegee.

YOU HAVE YOUR CHOICE OF WHITE, BLACK, SILVER, RED and DARK BLUE. (Other colors available by special request.)

This kit is cut from Quality ORACAL 651 OR HI-CAL High Gloss Vinyl.

IT IS VERY IMPORTANT THAT YOU STATE WHICH COLOR YOU WANT BY INCLUDING A NOTE OR COMMENT WHEN YOU PAY.

NOTE - THE IMAGE BELOW SHOWS THE KIT IN SILVER. YOU HAVE YOUR CHOICE OF ALL THE COLORS LISTED ABOVE.

RALLY STRIPE INSTALLATION INSTRUCTIONS - Install in a dry, wind free area. To install our stripe kits first take a pair of scissors and cut the roll striping into the lengths you will need for the hood and roof. Make sure to cut each piece a little longer than the section you are striping. Keep these sections dry and set them aside.

Remove any emblems that may get in the way of the stripe. (replace them after the stripes are applied)

Clean the application area with rubbing alcohol.

After the car is clean, mix in a spray bottle 20 ounces of water, 1/4 teaspoon of unscented clear liquid JOY and 1/2 teaspoon of Isopropyl Alcohol. (if you do cannot get clear liquid joy any dishwashing liquid will work)

I normally find the center of the car and then take a roll of masking tape and run it from the front to the back of the car. This will serve as a guide for lining up the stripes.

Once I have marked where the stripes will go I spray the car with soapy water and then I peel off the backing and spray the adhesive side of the first stripe with the soapy water as well. Position the stripe where you want it and slide it into place. For longer sections is it nice to have a second person help out. For the precut pieces I normally start at the top and work my way down the stripe. As long as the stripe and the car are wet with the soapy water you can work with the stripe. Keep the stripes you are not working with DRY.

Once the stripe is where you want it you simply squeegee it on. Spray a little soapy water on the stripe to allow the squeegee to glide over the stripe without scratching it. (wrapping the squeegee in a soft cloth will also protect the stripe from scratches) Repeat this process on all stripes and then trim any excess vinyl away with an exacto knife or razor blade. The precut pieces should require no trimming. Don't worry, if you make a mistake and need a replacement piece I can send you one for a small fee plus shipping.

TIP - for bumpers and other curved areas use a hair dryer to heat the material. This softens the vinyl and helps it to conform.

If you wish to order with a check or money order you can send $89.99 plus $8 shipping or $94.99 plus $8 shipping for the kit with pinstripes along with a description of what you are ordering to

Cole Farms Inc.
1610 Guam Lane
Gulf Breeze, Fl 32563

---

To order this kit via credit card or paypal for $89.99 plus $8 shipping click below:

---

---

To order this kit WITH A SEPARATE SHEET OF PINSTRIPES THAT ARE APPLIED AFTER THE MAIN STRIPES via credit card or paypal for $94.99 plus $8 shipping click below:

When you pay simply type in your color choice in the description box above the section where you put in your credit card information. If you pay with paypal put the color choice in the comments box. If you pay by mail just put in a note with the payment. You can also email me at the link above. These kits are available in WHITE, BLACK ,SILVER, RED, DARK BLUE. (Other colors available by special request.)

BACK TO MAIN PAGE FOR JEEP & CAR GRAPHICS