|
REFLECTIVE TAPE STORE PREFORMED THERMOPLASTIC HANDICAP SYMBOLS & LOGOS ITEMS SHIPPED "FAST" VIA UPS WITHIN THE U.S. Our Preformed Thermoplastic ADA handicap symbols are extremely durable, and can be applied by anyone using a broom and a simple heat torch. Designed for an extremely long life. 4-6 times thicker than standard painted logos. Available in single piece mats and in multiple piece stand alone logos.  |
|
HAVE A QUESTION OR NEED A SAMPLE? CLICK TO EMAIL STEVE COLE e-mail or call me at 850-934-3157 9am-9pm |
 CLICK HERE FOR AN INSTALLATION VIDEO Our thermoplastic handicap/disabled parking space supplies consist of 5 choices of logos which are outlined below and our 4" x 30' blue preformed thermoplastic pavement marking tape ROLLS. This product will last up to 5 times longer than paint. The logos have a non skid surface and the 4" rolls of striping are reflective via glass beads embedded in the tape. Our tapes and logos are simple to install using a broom and a propane torch for asphalt or a broom, torch and thermobond for cement. No contractor required. They are 90 mils thick and are extremely durable once installed. Since this is a melt on type product the tape will conform and bond to both moderately rough surfaces or smooth surfaces. When properly installed you will get years of service out of this material. It can handle any type of traffic. To apply simply broom or blow off the dry, oil free area to be striped, heat the area to about 300 degrees with a propane torch, lay out the stripe and then slowly heat the surface of the stripe or logo until a permanent bond is created. Once the material has cooled the area is ready for traffic. Please refer to the link above for complete instructions. It is important for this product to be installed properly. Note-for cement or concrete surfaces such as warehouse floors you will need to use "thermobond" which can be ordered at the bottom of this page. It creates an excellent bond with cement or concrete and substantially reduces the amount of heat necessary to install the thermoplastic striping. Thermobond can also be used on on asphalt to reduce application time. To use thermobond you mix an amount that you can use within 15 minutes and apply to either the back of the stripe, the pavement surface, or to both if you wish. Then lay the stripe down and heat the top of the stripe with a torch until the material conforms to the surface. (note that it does not take a tremendous amount of heat to get the material to conform) The thermobond will set in about 15 minutes and at that point the stripes are ready for traffic. Click here to order white & yellow rolls in 4" widths by the ROLL. Click here to order white, yellow & blue rolls in 4" - 24" widths by the CASE. Click here to order 12" WHITE material for Stop Bars and Crosswalks.
HANDICAP LOGOS 42" x 42" Handicap Logo Mat (White Logo with Blue Background) $440 per pack of 3 48" x 48" Handicap Logo Mat (White Logo with Blue Background) $500 per pack of 3 46" x 46" Handicap Logo Mat (White Logo with Blue Background & White Border) $475 per pack of 3 39" Tall Blue Handicap Logo (applied in sections, no background) $250 per pack of 3 39" Tall White Handicap Logo (applied in sections, no background) $250 per pack of 3 The logos come 3 to a pack and must be shipped on a pallet. You will need to call me at 850-934-3157 or email me at the link above to order these. Shipping cost for a pallet can vary from $50 - $200 depending on your location, however, a large amount of product can be shipped on one pallet. For example, shipping for 2 packs of logos would run about the same as shipping for 8 packs. If you only need rolls of striping you can order via the button above, however, when ordering rolls of striping AND logos we recommend you order over the phone so that we can put all of the product on the same pallet and reduce shipping cost. 4" ROLLS ($59.99 per roll plus shipping)
click below: ($299.99 per case plus shipping)
click below:  For bonding thermoplastic to cement surfaces use "thermobond". It is a heat activated adhesive specially designed for thermoplastic striping. Simply mix the amount you need, roll onto the ground or back of the stripe, lay on the ground and heat just enough to get the material to conform to the surface. The heat will activate the adhesive and create an excellent bond. Detailed instructions will be included with the thermobond. One gallon will adhere approximately 720 linear feet of 4" striping. Note - Thermobond may also be used on asphalt for superior bonding but is not necessary.) ($100.00 per gallon which includes shipping. This item will ship from the manufacturer and may arrive separately from your thermoplastic rolls.)
click below:
If you wish to order with a check or money order you can send payment along
with a description of what you are ordering to 
About our products - We carry the finest quality industrial/commercial reflective tapes, reflective iron on tape, non skid tapes and pavement marking tapes available. Our parking lot striping tapes are manufactured using the highest quality raw materials that result in a durable application that is resistant to heavy traffic, water and grease.
|